DIY Outdoor Slat Lounge Kit

3x1 Recycled Tube Steel brings this striking lounge kit together.  Created to be paired with our DIY Outdoor Slat Table & Bench - these rectangular shaped legs have a 37"L x 1.5"W slot for dimensional lumber, butcher block or your own uniquely sourced wood, composite materials.  Find instructions below for 2x8 lumber build (as seen in photos)

The Lounge Kit Includes :  2 Leg brackets, Steel Back Rest & Leveling feet. (wood & fasteners not included)

The slotted design offers superb rigidity for lasting & stable seating. These brackets can be used indoor or outdoor. 

Casters will add about 4" in height (3.65") when screwed all the way in. Leveling feet will add 0.4375" to 1.125" to the height depending on how far you screw in the foot.

Clear & Color Powder Coats

Our powder-coat finishes are scratch-resistant and rust-proof, so they don't need much care. Just be sure to touch up any exposed steel if you happen to drag them across rough surfaces, such as pavers, or scrape them with something sharp.

     You can attach your Slat Legs with just a few simple tools( Circular Saw, Rubber mallet, Hand Drill/Driver).  Here are a few basic steps to help you get started.  These instructions will be for the dimensional lumber build as seen in photos, best value build.  Feel free to use any wood, epoxy or polymer boards(if sturdy enough) as the seat and the back rest.  

• Two:  NOT WARPED 2" x 8" x 8' boards of premium pine lumber ( 14 feet of 2"x8" lumber per lounge seat) treated or untreated.  Treated has a greenish hue vs. Non-treated has a warmer orange hue. (actual width is 7.25")
• One: NOT WARPED 2" x 6" x 8' board of premium pine lumber ( 6 feet of 2x6 lumber needed per back rest)
• Circular Saw
• Drill/Driver
• Sanding Paper/Orbital Sander
• Rubber Mallet (to tap slats into slot)
• Tape Measure
• Pencil
• Deck Finish
• Finish Applicator ( Rag, Roller etc.)
• 1.25" Truss Screws
  
  

Step 1:  You will need 5(2x8) boards for lounge seat & 3 boards(2x8) for back rest. The length of your 5 seat boards are dependent on the width of your cushions.  Cut your boards to width of : cushions plus 6 inches(if seat cushion width is 28", add  6" to get board size, in this case = 34"). Dimensions of seat cushion in photos is 28"W x 28"L x 4" Thick.  Boards in photos were cut to a length of 34".  

Step 2:  Now cut your back rest boards.  If using large steel back rest, cut 3 boards to no less than 24" of length or if solid piece of wood cut to 20" x 24".  If using 3" bounce brackets cut to width of your preferred placement on seat. ( keep bounce brackets at least .25" from seat bracket so they don't touch to preserve finish) 

Step 3 : Sand and finish your boards for looks and longevity. (light sanding and deck finish applied using a roller were used for lounge in photos). Please follow instructions set by manufacturer for deck finish, curing times will vary.

Step 4: Turn your legs upside down on a flat surface, throw down some fabric first to protect the finish.  Now place your 5 boards into the 1.5" slot, starting with edge pieces first. Be sure to leave a small, equidistant space between boards for water to run out. If boards do not fit, rip or sand one board to compensate. Now attach your boards using #10 1.25" Truss head wood screws at for optimal fastening. 

Step 5 : Screw in Leveling feet

Step 6 : Grab a buddy. Confirm the Lounge Legs are securely attached, then turn your project right side up. 

Step 7 :  Now place your back rest on final board of seat.  Attach with #10 1.5" Truss head screws to board. 

Step 8 :  Now attach wood to back rest. Use the three 2x6 boards cut to 24" to the back rest.  Fasten using #10 Truss head screws. Now throw on your couch cushions.

Step 9 : Now Lounge & Enjoy!

As a company that focuses on creating custom sizes and that manufactures to your specification, returns can get a little tricky. We can accept returns for Quick Ship items within 30 days of delivery. 

We do not currently accept international returns. 

For our full return policy, please go here.